QUESTION 61
Scenario: An administrator plans to troubleshoot connections to the SSL virtual server configured on the NetScaler by using the WireShark tool. The administrator created a network trace file.
What will the administrator need to decrypt the network trace?
A. NS-root key
B. NS-server key
C. Private key of the root certification authority
D. Private key of the certificate that is bound to the virtual server
Answer: D
QUESTION 62
Scenario: A number of administrators received the following error when they attempted to connect to the Configuration Utility using a secured HTTPS connection:
The site’s security certificate is not trusted!
One of the administrators installed a certificate from a trusted Certificate Authority on the NetScaler and is planning to configure the Configuration Utility to use this certificate.
Which NetScaler command must the administrator run at the command-line interface to configure the Configuration Utility with the new certificate?
A. set ssl service
B. set ssl vserver
C. bind ssl service
D. bind ssl vserver
Answer: C
QUESTION 63
Scenario: A company currently has a working production XenApp and NetScaler environment. An administrator recently implemented a test NetScaler environment and tried to duplicate the NetScaler Gateway configuration from the production environment in the test environment. When the administrator configured the Secure Ticket Authority in the test environment, the Secure Ticket Authority showed a DOWN state. The administrator verified that the Secure Ticket Authority state shows as UP on the production NetScaler.
What should the administrator check to troubleshoot the issue?
A. NetScaler route table
B. NetScaler Gateway Resources
C. NetScaler Gateway Session Profiles
D. Secure Ticket Authority server IP address
Answer: A
QUESTION 64
When a user launches a published version of Notepad, the user receives the following error message:
“Cannot connect to the Citrix XenApp server.SSL Error: The proxy denied access to 10; STA393B6A5D1088; 9764757E39D0BEBB0BFC66E9EE146FF4 port 1494.”
What could be the cause of this error message?
A. Web Interface CANNOT reach the XML broker.
B. Web Interface CANNOT reach the XenApp server.
C. NetScaler Gateway CANNOT reach the XenApp server.
D. NetScaler Gateway CANNOT reach the Secure Ticket Authority server.
Answer: D
QUESTION 65
Scenario: An administrator configured link load balancing to balance outbound traffic between two Internet Service Providers. When testing the configuration, the administrator notices NetScaler is unable to connect to any external addresses.
Which mode should the administrator verify is enabled?
A. Layer 3
B. Layer 2
C. Use Subnet IP
D. Use Source IP
Answer: C
QUESTION 66
Which trap can an administrator set on a NetScaler system so that an alert is sent whenever an SNMP management application that does NOT have access privileges attempts to access a NetScaler?
A. loginFailure
B. accessFailure
C. accessDenied
D. authenticationFailure
Answer: D
QUESTION 67
Scenario: An administrator is planning the deployment of a NetScaler system for a large banking corporation. The bank has very stringent Internet security policies and auditing procedures. One of the requirements for the transaction auditing is that the web server logs record the original client IP addresses.
Which two features on the NetScaler could the administrator use to meet the auditing requirement? (Choose two.)
A. USIP
B. RNAT
C. USNIP
D. Edge mode
E. Client IP insertion
Answer: AE
QUESTION 68
A network administrator wants to ensure that connection multiplexing is enabled for all client connections that hita virtual server.
Which service type should the administrator select to enable connection multiplexing?
A. SSL
B. FTP
C. TCP
D. HTTP
Answer: C
QUESTION 69
What must an administrator configure when adding a new SNMP manager to a NetScaler Configuration Utility?
A. Source port
B. SNMP community string
C. Source interface Number
D. SNMP manager IP address
E. SNMP Trap Type (Basic and Advanced)
Answer: B
QUESTION 70
Scenario: An administrator is configuring a NetScaler system in one-armed mode The administrator has connected the NetScaler appliances to the network through a switch and will soon configure the appliances as a pair with HA enabled.
Which two steps should the administrator take to successfully configure HA in this environment? (Choose two)
A. Disable al unused network interfaces.
B. Ensure the NSP is unique on each node.
C. Ensure the NSP is identical on each node.
D. Change the default nsroot password on each node of the HA pair.
Answer: AD
If you want to pass the Citrix 1Y0-250 Exam sucessfully, recommend to read latest Citrix 1Y0-250 Dump full version.