Official 2014 Latest Citrix 1Y0-350 Dump Free Download(1-10)!

QUESTION 1
Scenario: For security reasons, the NSIP needs to be configured to only be accessible on interface 0/1, which is VLAN 300.
The NSIP address is 10.110.4.254 and the subnet mask is 255.255.255.0.
How would the network engineer achieve this configuration?

A.    set ns config -nsvlan 300 -ifnum 0/1
B.    set ns ip 10.110.4.254 -gui ENABLED -vrID 300
C.    add vlan 300
set ns ip 10.110.4.254 -mgmtAccess ENABLED
D.    set ns config -IPAddress 10.110.4.254 -netmask 255.255.255.0

Answer: A

QUESTION 2
Why would an engineer want to specify a TCP Profile for a specific service group?

A.    To enable use of features like SSL over TCP for that specific service group.
B.    To adjust the TCP settings for traffic to and from that specific service group.
C.    To use a specific SNIP for traffic to the back-end servers in that service group.
D.    To enable features like use source IP, TCP keep alive and TCP buffering for a specific service group.

Answer: B

QUESTION 3
A network engineer wants to optimize a published load balanced SSL virtual server for WAN connection with long delay, high bandwidth with minimal packet drops.
What would the network engineer use to do this type of optimization for the SSL virtual server?

A.    SSL policy
B.    TCP profile
C.    Compression policy
D.    Priority queuing policy

Answer: B

QUESTION 4
Scenario: The NetScaler is connected to two subnets. The NSIP is 10.2.9.12. The external SNIP is 10.2.7.3. The MIP for internal access is 10.2.9.3. Web servers, authentication servers and time servers are on the 10.2.10.0/24 network which is available through the 10.2.9.1 router. The external firewall has the 10.2.7.1 address. Traffic bound for Internet clients should flow through the external firewall.
Which command should be used to set the default route?

A.    add route 0.0.0.0 0.0.0.0 10.2.7.1
B.    add route 0.0.0.0 0.0.0.0 10.2.9.1
C.    add route 10.0.0.0 255.0.0.0 10.2.9.1
D.    add route 10.0.0.0 255.0.0.0 10.2.7.1

Answer: A

QUESTION 5
Some SSL certificate files may be missing from a NetScaler appliance.
Which directory should an engineer check to determine which files are missing?

A.    /nsconfig/ssl
B.    /nsconfig/ssh
C.    flash/nsconfig/
D.    /var/netscaler/ssl/

Answer: A

QUESTION 6
Scenario: An engineer has been hired to manage the content-switching configurations on the NetScaler. The user account for this engineer must have the standard rules that apply to the other administrators.
What should the engineer do to allow for the extra privileges?

A.    Modify the current Command Policy and then save the changes.
B.    Unbind the current Command Policy of the user account and then save the changes.
C.    Remove the custom Command Policy and then create one with the new requirements.
D.    Create a custom Command Policy and bind it to the user account with the highest priority.

Answer: D

QUESTION 7
A network engineer needs to configure smart card-based authentication on NetScaler Access Gateway.
Which type of authentication policy could the engineer configure in order to accomplish this task?

A.    Local
B.    RADIUS
C.    Certificate
D.    Secure LDAP

Answer: C

QUESTION 8
Scenario: The network engineer has created a monitor and bound it to a service group containing four web servers to verify that the web application responds. During routine maintenance one of the web servers is shut down; however, the server state remains UP and user requests are still attempting to communicate with the server.
What could be causing this problem?

A.    The server has been disabled.
B.    The monitor is not bound at the correct bind point.
C.    Health monitoring is disabled for the service group.
D.    The NetScaler configuration has not been saved since before the monitor was bound.

Answer: C

QUESTION 9
Scenario: An engineer is configuring services to allow load balancing of backend web servers on the internal network. The engineer bound multiple monitors to the first service, but notices that the service is reporting as DOWN. The monitor threshold default has NOT been changed.
What could be causing this issue?

A.    The service type is HTTP.
B.    One of the monitors’ tests is failing.
C.    Some of the monitors have a higher weight.
D.    The monitors are both reporting an UP status.

Answer: B

QUESTION 10
What should a network engineer configure to set high availability for a load balanced virtual server?

A.    Session persistence
B.    A backup virtual server
C.    Load balancing policies
D.    Load balancing services

Answer: B

If you want to pass the Citrix 1Y0-350 Exam sucessfully, recommend to read latest Citrix 1Y0-350 Dump full version.

clip_image001

Comments are closed.